<h2> Using the Balanset-1A Instrument </h2>
<h3> Preparing the Necessary Tools </h3>
<ul>
<li> accelerometers, laser rpm sensor, mounting stand, software application, and additional tools. </li>
<li> Connect the device to your PC using the USB interface and confirm the software installation. </li>
</ul>
<h3> Sensor Installation </h3>
<ul>
<li> Mount the vibration transducers securely on the machine's housing where vibrations are most pronounced, typically near the bearings. </li>
<li> Aim the optical rpm sensor at the rotating shaft and apply a reflective strip to the shaft for phase angle data acquisition. </li>
</ul>
<h3> Starting the Program </h3>
<ul>
<li> Launch the Balanset software on your computer. </li>
<li> Select the appropriate balancing mode: single-plane or two-plane, depending on the rotor type and your specific requirements. </li>
</ul>
<h3> Initial Vibration Measurement </h3>
<a href="https://vibromera.eu/wp-content/uploads/2024/11/2-Camera_01.png" target="_blank">
<img src="https://vibromera.eu/wp-content/uploads/2024/11/2-Camera_01.png" alt="2-Camera_01" style="width: 50%; display: block; margin-bottom: 10px;">
</a>
<ul>
<li> Run the rotor up to its operating speed. </li>
<li> The application will acquire data on vibration magnitude, rotational velocity, and phase angle to determine the initial imbalance state. </li>
</ul>
<h3> Trial Weight Installation </h3>
<a href="https://vibromera.eu/wp-content/uploads/2024/11/3-Camera-2_01.png" target="_blank">
<img src="https://vibromera.eu/wp-content/uploads/2024/11/3-Camera-2_01.png" alt="3-Camera-2_01" style="width: 50%; display: block; margin-bottom: 10px;">
</a>
<ul>
<li> Stop the rotor and attach a trial weight at a specific location on the rotor. The weight's mass can be specified within the software (e.g., in grams). </li>
<li> Resume rotor operation, and the program will capture the resulting changes in vibration amplitude and phase. </li>
</ul>
<a href="https://vibromera.eu/wp-content/uploads/2024/11/5-Camera_01.png" target="_blank">
<img src="https://vibromera.eu/wp-content/uploads/2024/11/5-Camera_01.png" alt="5-Camera_01" style="width: 50%; display: block; margin-bottom: 10px;">
</a>
<h3> Computing the Compensating Weight </h3>
<ul>
<li> Based on the measured data, the software automatically calculates the correction weight parameters: mass and installation angle. </li>
<li> These parameters are displayed on the screen as numerical data and graphs. </li>
</ul>
<a href="https://vibromera.eu/wp-content/uploads/2024/02/Bs1ManualEngV156-May2023-10448629.png" target="_blank">
<img src="https://vibromera.eu/wp-content/uploads/2024/02/Bs1ManualEngV156-May2023-10448629.png" alt="Bs1 Manual" style="width: 30%; display: block; margin-bottom: 10px;">
</a>
<h3> Installing the Correction Weight </h3>
<ul>
<li> Attach the computed compensating weight to the rotor as indicated by the software's output. </li>
<li> You can conduct interim measurements to confirm that the imbalance is decreasing as expected. </li>
</ul>
<a href="https://vibromera.eu/wp-content/uploads/2024/11/1-Camera-2_01.png" target="_blank">
<img src="https://vibromera.eu/wp-content/uploads/2024/11/1-Camera-2_01.png" alt="1-Camera-2_01" style="width: 50%; display: block; margin-bottom: 10px;">
</a>
<h3> Verification and Balancing Completion </h3>
<ul>
<li> With the compensating weight attached, operate the rotor and assess the level of any residual vibration. </li>
<li> The balancing procedure is finished if the remaining vibration is within the permissible limits specified in ISO 1940. </li>
<li> If the vibration is still outside acceptable limits, reiterate the process and fine-tune the compensating weight. </li>
</ul>
<h3> Generating a Documentation of the Balancing Results </h3>
<ul>
<li> The balancing results are saved in the software's archive. You can create and print a report containing vibration data, correction weight mass, and its installation angle. </li>
</ul>
<h3> Concluding Steps and Verification </h3>
<ul>
<li> Ensure all applied weights and attached sensors are firmly fixed in their designated positions. </li>
<li> Confirm that the rotor spins freely and quietly, without any unusual sounds or vibrations. </li>
<li> If the rotor operates within a larger assembly, check the functionality and interplay of all interconnected parts. </li>
</ul>
<p> This process allows for precise imbalance correction, reducing vibration and extending equipment life. </p>
Instagram: https://www.instagram.com/vibromera_ou/
Youtube : https://youtu.be/guA6XJ-ArZM?si=vmkuX7RILzKBl0zL
Our website about <a href="https://vibromera.eu
"> Balancing of pulley </a>